产品展示
您当前的位置：首页 » 产品展示 » 专用仪器仪表 » 个人剂量仪/个人剂量报警仪 CSD-BH3084
| 产品名称： | 个人剂量仪/个人剂量报警仪 CSD-BH3084 |
| 产品型号： | CSD-BH3084 |
| 品牌： | 70 |
| 产品数量： | |
| 产品单价： | 面议 |
| 日期: | 2023-10-19 |
个人剂量仪/个人剂量报警仪 CSD-BH3084的详细资料
1.个人剂量仪/个人剂量报警仪 型号：CSD-BH3084主要术标：
1、探 测 器：GM计数管
2、探测辐射：γ和X射线
3、测量范围：
A、剂量当量率: 00.01usv/h～01.00 msv/h
B、剂量当量： 00.01usv～99.99 msv；
4、报警阈值：可设置
5、相对误差：＜±20%（00.01usv/h～01.00 msv/h）
6、能量响应：＜±30%（50KeV～1.3MeV）
7、欠压示：当电池电力不足时仪器停止作，缺电标灯亮
8、外形尺寸：118mm×65mm×25mm
9、重量：＜110g
2.汽车尾气检测系统 汽车尾气检测仪 型号：NTP1-HPC508
NTP1-HPC-508 汽车排气分析仪（ASM况法专用）
NTP1-HPC-508汽车排气分析仪可应用于稳态况法（ASM法）和简易瞬态况法（Vmas）的系统设备配套，是简易况法行汽车检测的专用分析仪器。仪器采用口专业检测器，按照美BAR-97的有关要求行设计和制，满足新标GB18285-2005中稳态况法的测量规范和度要求，可测量CO、HC、CO2、O2、NO、λ及AFR、发动机转速、油温，备有多种标气入口，自动反吹能，满足北京地方标准及有关标准的使用要求。也可广泛应用于机动车排气污染分析连续检测、发动机排放分析研究等。
主要能与特点:
★、分辨率、本仪器满足欧I-IV标准车辆的排放检测。
★自动调零、自动清洗、自动温度补偿、压力补偿、。
★具备气路泄漏检查、流量监控、HC残留检测、反吹清洗取样管气路。
★备有ASM法、双怠速检测和普通怠速检测多种测量模式、发动机转速、油温等各项参数测量能。
★可车牌号输入及2000组数据存储、备查能、时钟显示。
★可选用寿命长、度的红外（NDIR）NO分析平台，反应速度比传统电化学原理检测器快三倍。
★可选用寿命长、度的红外（NDIR）NO分析平台，反应速度比传统电化学原理检测器快三倍。
主要术参数：
测量范围 HC：0～10000×10-6（ppm）vol CO:0～10×10-2(%)vol
CO2:0～20×10-2(%)vol O2:0～25×10-2(%)vol
NOx:0～5000×10-6（ppm）vol
示值误差
|
气体
|
量程
|
示值误差
|
|
|
误差
|
相对误差
|
||
|
HC
|
0 ~ 2,000 (ppm) vol
|
±4×10-6(ppm) vol
|
±3%
|
|
2,001 ~ 5,000 (ppm) vol
|
±5%
|
||
|
5,001 ~ 9,999 (ppm) vol
|
±10%
|
||
|
CO
|
0 ~ 10.00 (%) vol
|
±0.02×10-2(%) vol
|
±3%
|
|
10.01 ~ 14.00 (%) vol
|
±5%
|
||
|
CO2
|
0 ~ 16.0 (%) vol
|
±0.3 ×10-2 (%) vol
|
±3%
|
|
16.1 ~ 18.0 (%) vol
|
|
±5%
|
|
|
O2
|
0 ~ 25.00 (%) vol
|
±0.1 ×10-2 (%) vol
|
±5%
|
|
NOx
|
0 ~ 4,000 (ppm) vol
|
±25 ×10-6(ppm) vol
|
±4%
|
|
4,001 ~ 5,000 (ppm) vol
|
±8%
|
||
分辨率 HC：1×10-6（ppm）vol CO: 0.01×10-2(%)vol CO2: 0.1×10-2(%)vol
O2: 0.01×10-2(%)vol NOx:1×10-6（ppm）vol λ:0.01
重复性 CO：0～7.00% ≤±0.02%或±2%读数， 7.01～10.00% ≤±3%读数
CO2：0～10.00% ≤±0.1%或±2%读数， 10.01～16.00% ≤±3%读数
HC：0～1400ppm ≤±3ppm或±2%读数， 1401～2000ppm ≤±3%读数
O2：0～10.00% ≤±0.4%读数， 10.01～25.00% ≤±1%读数
NOx：≤±8ppm或±3%读数。
注：以上误差中满足其中项要求即可。
HPC-508 automobile exhaust analyzer(ASM)：
HPC-508 automobile exhaust analyzer can be applied to steady-state condition method (ASM method) and simple transient conditions France (Vmas) system equipment package, is a simple method for vehicle inspection conditions dedicated analytical instruments. Equipment imported professional detector, according to the U.S. BAR-97 with the relevant requirements for the design and manufacture to meet the latest national standard GB18285-2005 in the steady-state condition method of measurement standards and accuracy requirements, measurable, CO, HC, CO2, O2, NO , λ, and AFR, engine speed, oil temperature, a wide range of standard gas entrance, automatic cleaning function, to meet the Beijing local standards and national standards relating to use requirements. Can also be widely used in motor vehicle exhaust pollution analysis of continuous testing, engine emission analysis studies.
Main Features:
◆High-precision, high resolution, the instrument to meet the European I-IV standard emissions testing of vehicles.
◆Auto-zero, automatic cleaning, automatic temperature compensation, pressure compensation.
◆Have the gas line leak inspection, traffic monitoring, HC residue testing, cleaning gas sampling tube cleaning path.
◆With ASM method, pairs of test and normal idle speed idle test a variety of measurement mode, engine speed, oil temperature, and other parameter measurement function.
◆License plate number can be entered and the 2000 set of data storage, reference function, clock display.
◆Can choose long life and high precision infrared (NDIR) NO analysis platform, the reaction rate than the traditional three times faster electrochemical detection principle.
◆Auto-zero, automatic cleaning, automatic temperature compensation, pressure compensation.
◆Have the gas line leak inspection, traffic monitoring, HC residue testing, cleaning gas sampling tube cleaning path.
◆With ASM method, pairs of test and normal idle speed idle test a variety of measurement mode, engine speed, oil temperature, and other parameter measurement function.
◆License plate number can be entered and the 2000 set of data storage, reference function, clock display.
◆Can choose long life and high precision infrared (NDIR) NO analysis platform, the reaction rate than the traditional three times faster electrochemical detection principle.
Main technical parameters:
Test Scope：HC：0～10000×10-6（ppm）vol CO：0～10×10-2(%)vol
CO2：0～20×10-2(%)vol O2：0～25×10-2(%)vol NOx:0～5000×10-6（ppm）vol
Shows the value error：
|
Gas
|
Range
|
Indication error
|
|
|
absolute error
|
relative error
|
||
|
HC
|
0 ~ 2,000 (ppm) vol
|
±4×10-6(ppm) vol
|
±3%
|
|
2,001 ~ 5,000 (ppm) vol
|
±5%
|
||
|
5,001 ~ 9,999 (ppm) vol
|
±10%
|
||
|
CO
|
0 ~ 10.00 (%) vol
|
±0.02×10-2 (%) vol
|
±3%
|
|
10.01 ~ 14.00 (%) vol
|
±5%
|
||
|
CO2
|
0 ~ 16.0 (%) vol
|
±0.3 ×10-2 (%) vol
|
±3%
|
|
16.1 ~ 18.0 (%) vol
|
|
±5%
|
|
|
O2
|
0 ~ 25.00 (%) vol
|
±0.1 ×10-2 (%) vol
|
±5%
|
|
NO
|
0 ~ 4,000 (ppm) vol
|
±25 ×10-6(ppm) vol
|
±4%
|
|
4,001 ~ 5,000 (ppm) vol
|
±8%
|
||
3.烟度计 型号：NTP1-HPC601
主要能特点：
体化结构设计；
采用分流式取样术、柴油机加速、减速和稳速时均可测量烟度；
数据自动线性化处理，可显示不透光度N、光吸收系数K和对应滤纸式烟度值SF；
亮度数码显示；
采用“空气幕”术保护光学系统免受污染；
检测室自动恒温控制，可防冷凝而影响测试度；
附自动时间显示,可选配转速测量和油温测量；
出现故障自动诊断显示所在单元；
配内置打印机（或数字RS－232A接口或模拟接口）。
主要术参数：
体化结构设计；
采用分流式取样术、柴油机加速、减速和稳速时均可测量烟度；
数据自动线性化处理，可显示不透光度N、光吸收系数K和对应滤纸式烟度值SF；
亮度数码显示；
采用“空气幕”术保护光学系统免受污染；
检测室自动恒温控制，可防冷凝而影响测试度；
附自动时间显示,可选配转速测量和油温测量；
出现故障自动诊断显示所在单元；
配内置打印机（或数字RS－232A接口或模拟接口）。
主要术参数：
测量范围 不透光度N:0～(相当烟度值0～10FSN)
光吸收系数K:0～16.06m-1
示值误差 ≤±2%(测量值)
稳定性 自动校零，量矩漂移≤±1%/4h
重复性 重复误差≤±1%
分辨率 0.1%
输出方式 数字直读显示，可附打印机打印烟浓度(暗度)zui大值，测试
时间、日期等。可附接口与计算机联网
测量烟度温度 70℃(自动恒温)，当温度误差≥±10%时，温度及错误示
灯亮
环境条件 温度0～40℃，相对湿度≤90%
电源 AC100-240V 50Hz 消耗率150VA
外形尺寸（含支架） 160mm(深)×400mm(宽)×480mm()
重量 约8kg
Main Features:
◆Integrated Structural Design
◆Adopted a triage-type sampling technique, diesel engine acceleration, deceleration, and steady speed can be measured when the smoke
◆Linear automatic data processing, can be displayed opacity degrees N, light absorption coefficient K and the corresponding value of filter paper-type smoke SF
◆High-brightness digital display;
◆Use of "air curtain" technology to protect the optical system from pollution
◆Automatic detection of room temperature control, anti-condensation can affect the testing accuracy
◆Automatically attached to the time display, and optional speed measurement and oil temperature measurement
◆Show where the failure of automatic diagnosis unit;
◆Equipped with built-in printer (or digital RS-232A interface or analog interface)
◆Adopted a triage-type sampling technique, diesel engine acceleration, deceleration, and steady speed can be measured when the smoke
◆Linear automatic data processing, can be displayed opacity degrees N, light absorption coefficient K and the corresponding value of filter paper-type smoke SF
◆High-brightness digital display;
◆Use of "air curtain" technology to protect the optical system from pollution
◆Automatic detection of room temperature control, anti-condensation can affect the testing accuracy
◆Automatically attached to the time display, and optional speed measurement and oil temperature measurement
◆Show where the failure of automatic diagnosis unit;
◆Equipped with built-in printer (or digital RS-232A interface or analog interface)
Main technical parameters:
Test Scope：No light transmission N:：0～ (equivalent to smoke value 0 ~ 10FSN)
Light absorption coefficient K：0-16 .06 m-1
Shows the value error：≤ ± 2% (measured value)
Stability：Automatic zero, volume moments drift ≤ ± 1% / 4h
Repeatability：Repeat the error ≤ ± 1%
Resolution：0.1%
Output Mode：Digital direct-reading shows that smoke concentrations can be attached
Shows the value error：≤ ± 2% (measured value)
Stability：Automatic zero, volume moments drift ≤ ± 1% / 4h
Repeatability：Repeat the error ≤ ± 1%
Resolution：0.1%
Output Mode：Digital direct-reading shows that smoke concentrations can be attached
printer (dark degrees) the maximum test time, date and so on. Can be
attached to interface with the computer network
Measurement of smoke temperature：70 ℃ (automatic constant temperature), when
Measurement of smoke temperature：70 ℃ (automatic constant temperature), when
the temperature error of ≥ ± 10%, the temperature and the error
indicator light
Environmental conditions：Temperature 0 ~ 40 ℃, relative humidity ≤ 90%
Power：AC100-240V 50Hz Power consumption 150VA
Dimensions (with stand)：160mm (depth) × 400mm (width) × 480mm (H)
Weight：about 8kg
Environmental conditions：Temperature 0 ~ 40 ℃, relative humidity ≤ 90%
Power：AC100-240V 50Hz Power consumption 150VA
Dimensions (with stand)：160mm (depth) × 400mm (width) × 480mm (H)
Weight：about 8kg
温馨提示：以上产品的资料和图片都是按照顺序相对应的